 |
 |
 |
|
KEY FEATURES
- Advanced Silver/Carbon filled epoxy
- Excellent electrical conductivity, volume resistivity ~0.005 Ω·cm
- Perfect for die attachment and solderless interconnections
- Glass transition temperature 103 °C
Intro
Conductive epoxies can be used to form an electrically conductive bond between dissimilar materials eliminating the need for soldering. Traditional silver-based epoxy materials require up to 80% weight load of silver fillers and as a result tend to be costly, brittle and prone to mechanical failure.
Our Conductive Silver/Carbon Epoxy G6E-NS10™ has been developed based on advanced proprietary technology that requires 25% or less silver content to be at par with leading silver based epoxies in terms of electrical properties. This improvement not only brings price of the material down but also makes G6E-NS10™ less prone to fracture and allows for stronger adhesion to the target substrate.
Conductive epoxies can be used to form an electrically conductive bond between dissimilar materials eliminating the need for soldering. Traditional silver-based epoxy materials require up to 80% weight load of silver fillers and as a result tend to be costly, brittle and prone to mechanical failure.
Silver/Carbon Epoxy G6E-NS10™ is a two component adhesive for high performance bonding, sealing and coating purposes. G6E-NS10™ is intended to be cured at elevated temperatures. It can cure at room temperature in 60 hours or much more rapidly at elevated temperatures. Recommended curing temperature is 150°C. Volume resistivity of as low as 0.005 Ω·cm can be achieved under optimum curing conditions.
G6E-NS10™ has smooth paste like consistency after mixing and bonds well to a wide variety of substrates including metals, composites, ceramics, glass and plastics. It, however, has limited adhesion to rubber and silicon-based materials. This product is recommended for electronic packaging applications such as die attachment and solderless interconnections, component repair, display interconnections.
Product Info
TWO COMPONENT SYSTEM: Part A – smooth thixotropic dark grey paste,
Part B – smooth thixotropic silver paste.
THE MIX RATIO: 100 (Part A) to 100 (Part B) by weight.
CURING INSTRUCTIONS: Best results are obtained when product is cured at
one of the following schedules: 60 hours @ 25°C, 3 hours @ 70°C or 1 hour @
150°C
COLOR: Silver grey
POT LIFE: 4 hours
GLASS TRANSITION TEMPERATURE: 103°C (cured at 150°C)
MIXED VISCOSITY AT 25°C/77°F: 150 – 155 Pa.s
HARDNESS, SHORE: >60D
VOLUME RESISTIVITY: ~ 0.005 Ω·cm
SHELF LIFE: 6 months at 25°C in unopened, unmixed containers. Stores and
ships at room temperature—no freezing or dry ice required
MIXING INSTRUCTIONS: Stir both components before use. Add Part B to Part
A and mix slowly until uniform in a separate container.
SAFETY & HANDLING: Please read the SDS before use. Use it with adequate
ventilation. Keep away from sparks and open flames. Avoid prolonged contact
with skin and breathing of vapors. Wash with soap and water to remove from
the skin.
PACKAGING: Part A and Part B are packaged in jars with quantities of 10g,
20g and 50g each. This epoxy can be customized to any quantity as per the
customer’s requirement.
Application Notes
- Attachment of electro optical components
- Grounding
Repair of defect traces / tracks or creating smooth jumpers on PCB board.
- Lightning Strike Protection and EMI/RFI Shielding
- Lower temperature bonding of electrical modules
- High frequency shields, waveguides
- Terminal attachment to solar cell panels
- Quick and inexpensive mounting of LEDs
- Conductive traces on 3D printed parts
- Radio-frequency identification (RFID) tags
- 3D antennas
Easy repair of household electronics and car rear shield heater.
|
|
|
 |
|
 |
|